Hougen HMD 150 Mag Drill -
Low Profile
1-3/8″ Hole Dia. x 1″ Depth of Cut
This is the largest Hougen Low Profile Magnetic Drill.
The Hougen HMD150 is small, powerful, and a has a full 1″ depth of cut.
The HMD150 is a fabricator’s dream. It gets into tight spots with the low profile 7-13/16″ height.
Also it has the new lift detection safety feature, eliminating safety switch adjustments.
The Hougen Low Profile Mag Drill uses the Rotaloc PlusTM cutters from Hougen. It can also use the RotalocTM Annular Cutters, specially designed stack cut geometry for truck frames.
They have a quick release shank for quick cutter changes.
Rugged and full of power the HMD150 is great tool for construction and fabrication. The HMD151 is the 230V version.

Easy to carry, store, and transport.

Easy to carry, store, and transport.

The Hougen HMD 904 Magnetic Drill is the latest evolution of Hougen’s popular mag drills. It keeps the important attributes of the HMD904′s predecessor and made it better because:

• This new Hougen magnetic drill has a more powerful motor so you can drill large holes without stalling deep in the cut.
• The cost of magnetic drill motor wear replacement parts has been lowered by 1/3 over the old style motor.
• The new magnetic drill design increases the drill point breakaway to 820 lb.
• The magnetic drill weight has been lowered to just 27.5 lb.
• The magnetic drilling capacity is increased to 1-1/2″ diameter with a 2″ depth-of-cut.
• Hougen’s new magnetic drill ergonomic handles improve operator efficiency

Hougen HMD 115 Mag Drill -
Low Profile
1-1/16″ Hole Dia. x 3/4″ Depth of Cut
The powerful Hougen Low Profile Magnetic Drill HMD115 is an ultra low profile, lightweight 21 lb mag drill with a quill feed arbor.
The low profile allows this mag drill to be used in very tight spaces which would be otherwise impossible to drill with a standard magnetic drill.
The Hougen Low Profile Mag Drill has removable handles allowing the drill to be operated from either side and with handles removed, the hex head allows use of a socket wrench for ratcheting the feed.
Handles lock for carrying. The arbor has a bayonet-style twist and lock tool mounting for quick cutters change outs.
The Hougen Low Profile Mag Drill HMD115 uses RotalocTM Annular Cutters, specially designed stack cut geometry for truck frames.
For safety, the motor switch must be continuously pressed during operation and the motor will not run without the magnet switch “ON”.
Rear mounted controls optimize ergonomics. Convenient carrying case and safety strap is standard. The HMD111 is the 230v version.

Get a grip on cylinders with Boagrip

BOAGRIP ™ is the safest, fastest and easiest way to lift, carry and suspend cylinders.

• Tested and Proven

• Enables Easy Lifting

• Holds Securely for Hoisting

• Adjusts to Cylinders 4 to 15 Inches Diameter

Easy to carry, store, and transport.

Provide D-Wipe® Towels (#WT-150 or WT-040) for quick clean up of hands without water. Ideal near the firing line and at all outdoor ranges. Convenient locking wall bracket (#DW-150L) will keep towels in place and available.

Provide D-Wipe® Towels (#WT-150 or WT-040) for quick clean up of hands without water. Ideal near the firing line and at all outdoor ranges. Convenient locking wall bracket (#DW-150L) will keep towels in place and available.

New! Miller’s exclusive multi-voltage plug (MVP™) allows connection to 115 or 230 V receptacles without tools – choose the plug that fits the receptacle and connect it to the power cord.

Portable in the shop or at the job site – at 13.2 lb the shoulder strap allows the operator to easily move from location to location. Comes with X-Case and leads.

Auto-Line™ circuitry automatically connects to 115 – 230 VAC, single-phase power without removing the cover to relink the power source.

Low OCV Stick reduces open-circuit voltage (OCV) to 12 – 16 VDC when power source is not in use.

Adaptive Hot Start™ for stick arc starts prevents electrode from sticking.

Single Amperage Range allows operator to accurately set amperage on both 115 V or 230 V primary power.

Fan-On-Demand™ operates only when needed reducing noise, power consumption, and the amount of airborne contaminants pulled through the machine.
Maxstar® 150 S
Best in class – provides maximum portability and performance in the most compact Stick package in the industry. Packs dependability and performance all in one machine.

Wind Tunnel Technology™
Internal air flow that protects electrical components and PC boards from dirt, dust, debris… greatly improving reliability.

LVC™ Line Voltage Compensation Keeps output of the power source constant regardless of fluctuation in input power ± 10%.

Adaptive Hot Start™
for Stick
Automatically increases output amperage at the start of a weld should the start require it and prevents the electrode from sticking and creating an inclusion.

The Millermatic 140 mig welder with Auto-Set offers all the benefits of the standard Millermatic 140, but adds Auto-Set to eliminate the guesswork. Use Auto-Set when you want the speed, convenience and confidence of pre-set controls. Simply set the wire diameter, set the material thickness, and go! The Auto-Set control automatically sets your welder to the proper parameters. It is available when welding mild steel with solid wire and only works with .024 and .030 solid wires and C25 shielding gas (75% Argon, 25% CO2).

When not within the Auto-Set profiles, use the manual mode to set the weld parameters you desire. The parameter door chart lists voltage and wire feed speed settings options.

For use exclusively in the HMD111/115 and HMD150/151 magnetic drills. Made of M42 H.S.S. they have a bayonet style twist lock shank for fast tool change over requiring no tools to install in the drill’s arbor. For optimum cutter tool life and cutter efficiency use Slick-StikTM lubricant.

2 lb Spools

Available in .025″ or  .030″

Silicon Bronze (Everdure) mig wire on 2 Lb Spools.

Skullgard Caps and Hats feature heavy-duty construction for use in steel mills and other heavy industries where high temperatures are common.

Skullgard Caps and Hats meet or exceed the applicable requirements for a Type I helmet (top impact) as outlined in ANSI Z89.1 2003,Class G electrical-low voltage)

MSA Skullgard hard hats are built with heavy-duty materials for use in steel mills and other industries where high temperatures require extra protection and safety. The full brim style is an added safety feature.
Skullgard Caps and Hats meet or exceed the applicable requirements for a Type I helmet (top impact) as outlined in ANSI Z89.1 2003,Class G electrical-low voltage)

X-TREME™ Versatility – Auto-Line provides state-of-the-art flexibility. Automatically connects to 115-230 VAC, single-phase power, 50/60 Hz, without removing covers to relink the unit. No longer is there a concern if you have the correct machine for the shop or job site.

X-TREME™ Protection – model with
X-CASE™ provides ultimate protection during transport and storage. Additional space ideal for MVP plugs, consumable box, as well as gloves, eye protection, etc.

X-TREME™ Portability – Portable in the shop or at the job site – at 18 pounds the shoulder strap allows you to easily move from location to location.

Miller’s exclusive multi-voltage plug (MVP™)allows connection to 115 or 230 V receptacles without tools – choose the plug that fits the receptacle and connect it to the power cord.

LVC™ line voltage compensation provides peak performance power under variable conditions (power fluctuations up to +/-15%) for steady cuts and cleaner ending cuts.

Can be powered by any Miller engine drive with generator power (e.g. Bobcat™) or equivalent competitive equipment.

LED indicators for pressure, power, cup and temperature allow faster troubleshooting, eliminating unnecessary downtime.

Ergonomic design ICE-27T torch with increased comfort, safety trigger, and improved swirl ring and cup.

Factory pre-set air – no need to adjust the air pressure! The unit automatically regulates the proper internal air pressure to the torch.

Gas/air filter/regulator inside the power source provides added protection during transportation. Standard air connection on back panel for easy gas or air hookup.

Starts without high-frequency so it will not interfere with or damage controls or computers.

includes heavy-duty clamp.

The Tig-Pen is the first manual welding wire feeder that truly makes sense. It is held in the hand like an ordinary pencil. Use any diameter wire from 0.03″ to 0.125″. The wire feeds in a smooth continuous motion to the weld pool. Virtually all of the wire is consumed. Brushed aluminum only.

Everything you need for servicing air conditioning systems, cleaning coils, purging or pressure testing pipes and fixtures, even inflating tires. Add a bottle of nitrogen and you are ready to go. We sell this unit regularly for $199 but for this special summer sale, get this great 10 piece kit for only $169!